Electric surgical bed MST-E300A

Brochure: Electric surgical bed MST-E300A.pdf
Ideal for :

– abdominal surgery

– neurosurgery

– ophthalmology

– ENT

– obstetrics

– gynecology

– urology

– spine surgery

Chair technical characteristics:

• Power 220V
• Frequency 50Hz
• Power 200VA
• Made of stainless steel
• Easy to move and has reliable stability
• Total chair length: 2100 mm
• Total width (including armrests): 830mm
• Chair width: 550 mm Base width: 520mm
• Height: 750mm-1050mm (electric)
• Trendelenburg (forward): 25° (electric)
• Reverse-trendelenburg (back): 25° (electric)
• Side tilt (right): 15° (electric)
• Side tilt (left): 15° (electric)
• Back plate (up): 50° (electric)
• Back plate (down): 30° (electric)
• Head plate (up): 90° (hydraulic)
• Head plate (down): 90° (hydraulic)
• Foot plate (down): 90°, 180 extension °, detachable (hydraulic)
• Waist lift: 120mm (mechanical)
• Maximum weight: 135 kg

Standard configuration:

• Leg frame: 2 sections
• Body frame: 2 sections
• Armrests: 2 sections
• Anesthesia saddle: 1 section

Instructions for use:

1. The lifting of the bed surface, the lifting of the back plate, the tilting of the bed forward and backward, left and right, and the shifting forward and backward are completed by the motor push mechanism, which can be controlled by pressing the button with the remote control. The inclination of the back plate and backrest, left and right, as well as the height and angle can be adjusted within the adjustment range.
2. When the head plate is folded up and down, pull the foot handle with your hand, adjust the angle within the adjustment range, and loosen the foot handle to fix the position.
3. Foot plate: DST-1 split plate type: left-right separate operation. Pull the spring-loaded handle to make the foot plate go down. If the seat plate and the foot plate connection button are loosened to the left or right, the button can be fixed when the angle is reached.
4. The base of the surgical bed is equipped with a nylon wheel that can be moved. Fixed legs can be used to press the brake pedal, so that the pedal locks the brake pin, fixing the surgical bed.
5. Waist plate: lifting with worm screw and worm gear. After the screwing mechanism is completed, insert the crank into the lifting opening of the lumbar plate when lifting, and lift the handle to lift the lumbar plate. If the support plate is folded, lower the waist to the lowest position. Avoid collisions.

Attachments
1. Slider: The arm-related part has a single-slot slider, which is used to fix all accessories.
Armrest: first fix the arm bracket to the guide of the operating bed, adjust the knob at the lower end of the arm to reach the desired position, and fasten the strap through the fastener.
2. Leg bracket: first the single-slot slider is inserted into the guide, then the leg bracket is inserted into the round hole of the slide block, and the handle of the slide block can be fixed.
Anesthesia base: The anesthesia case is inserted into the two empty spaces of the slider and can be fixed by tightening the handle.

Maintenance methods
When the operating table is under maintenance and the fault is dealt with, the power supply is first cut off, the protective cover of the operating table column is removed, the cover is opened, the base fixing screws are removed, and the brake pedal and brake pin are removed, and the base shield can be maintained and repaired. When the fuse is replaced, remove the 2 fuse covers and replace the fuse with the new fuse.

After using the operating table, clean it and keep it dry.

3. Clean the operating table, use a soft cloth or sponge dipped in alcohol cloth. Use a soft cloth or a disinfectant solution dipped in a sponge for disinfection.

4. Common faults can be dealt with, while other faults can be reported to the factory.